first run
ath0: ath_rx_proc: no mbuf! ath0: ath_rx_proc: no mbuf! ath0: ath_rx_proc: no mbuf! ath0: ath_rx_proc: no mbuf!
interface recovers
second run
after the second run interface ath0 goes ofline.
benchmark settings:
TIMES=14000 PROTO=UDP TIME=10
uname -a
FreeBSD openping 7.1-PRERELEASE FreeBSD 7.1-PRERELEASE #0: Wed Oct 1 23:55:47 CEST 2008 root@bert.opencommunitycamp.org:/usr/obj/usr/src/sys/TINYBSD i386
dmesg
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-PRERELEASE #0: Wed Oct 1 23:55:47 CEST 2008
root@bert.opencommunitycamp.org:/usr/obj/usr/src/sys/TINYBSD
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (233.32-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (128 MB)
avail memory = 121942016 (116 MB)
wlan: mac acl policy registered
kbd0 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
ath0: <Atheros 5212> mem 0x80000000-0x8000ffff irq 12 at device 13.0 on pci0
ath0: [ITHREAD]
ath0: WARNING: using obsoleted if_watchdog interface
ath0: Ethernet address: 00:0b:6b:34:58:70
ath0: mac 5.9 phy 4.3 radio 3.6
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x1000-0x10ff mem 0x80040000-0x80040fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0
nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:05:4b:4c
sis0: [ITHREAD]
Geode GPIO@ = f400
Geode PC Engines WRAP.2B/2C v1.11 tinyBIOS V1.4a (C)1997-2005
isab0: <PCI-ISA bridge> port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <multimedia, audio> at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
pci0: <serial bus, USB> at device 19.0 (no driver attached)
cpu0 on motherboard
orm0: <ISA Option ROM> at iomem 0xe0000-0xe7fff pnpid ORM0000 on isa0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
Timecounters tick every 1.000 msec
ipfw2 initialized, divert enabled, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
ad0: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR> error=4<ABORTED>
ad0: 122MB <TOSHIBA THNCF128MMA 3.10> at ata0-master BIOSPIO
Trying to mount root from ufs:/dev/ad0a
bridge0: Ethernet address: a6:84:de:af:bd:be
